MeldaProduction updates all effects and MPowerSynth to v10.05

MeldaProduction has updated all effect plugins and MPowerSynth to 10.05, providing several new features, optimizations, improvements and fixes.

Changes for effects in 10.05:

Note: Backward compatibility has not been fully maintained for MMultiBandConvolution - settings are remembered properly, but automation parameters have been removed and replaced with multiparameters (via which you can automate anything).

Note: While backward compatibility is strictly maintained, in order to provide higher multiparameter bank mode accuracy, the new format is different from the previous one, hence settings stored with the new versions won't be loaded properly with previous versions. The should be no need to roll back to older versions, but it is an important information anyway.:

• Added several active presets to MMultiBandConvolution.
• MMultiAnalyzer now allows reordering of graphs.
• Added Modulation to both taps in MMultiBandConvolution (including MXXX).
• Added Crest meter to MLoudnessAnalyzer (including MXXX).
• When searching through presets the total number of presets are displayed along with the number of matching presets.
• All file browsers now provide Delete key to delete the selected file.
• MMultiAnalyzer highly optimized.
• Added Analog LP crossover to (MStereoProcessor including MXXX).
• Added active preset selection to TurboComp and TurboEQ in MXXX.
• Added Enable parameter to multiparameters, which can be used to enable/disable the control on the easy screen.
• Added "XY pad centered" editor mode to all multiparameters.
• Clicking time graph settings while the settings are already open will close the window now.
• VST parameter names are now reported smartly shortened instead of truncated.
• Added DC filter switch to MWobbler (including MXXX).
• Added HP & LP filters to MPhatik (including MXXX).
• Improved quality of all noise generators and algorithms based on them. Note that there may be a slight difference in sound, hardly noticeable though.
• Auto-listening a band in low-pass/high-pass mode in all parametric equalizers auditions the opposite filter - hence you listen what is being cut.
• Bands in all parametric equalizers/comb filters now also show a line up, for easier workflow when using analyzers. The lines are visible only if the band is enabled.
• Added Switcher and Selector multiparameter editor modes.
• Added MXXX FX into MXXX providing a full MXXX instance inside MXXX (and any sublevel). Note that only multiparameters can be accessed from the main instance.
• System cursors are now used on Windows due to compatibility reasons on some HiDPI devices.
• Style wizard has been discarded. Instead a Set current style as default button has been added.
• Bank values for all multiparameters are now stored with extreme accuracy.
• MNotepad keyboard can be hidden now.
• Added Sync mul to DelayTap and Feedback FX in MXXX.
• Added Tablet mode back, just in case it is needed.
• Fix: MXXX often didn't show a help button for the active preset (the info was available via F1 / ctrl+H though).
• Fix: First parameter of MStereoScope didn't have a name.
• Fix: Loading graph presets could lead to have some points in the middle unavailable to move in some places.
• Fix: A multiparameter in Switch mode could cause a freeze in certain situations.
• Fix: Multiparameters accessing ranges of secondary parameters of other multiparameters were not showing the target units.
• Fix: Equalizer/comb points could jump a little when started dragging.
• Fix: Reordering multiparameters sometimes didn't keep relations between different multiparameters controlling each other.
• Fix: Analyzers could crash when changing Time resolution.
• Fix: Left clicking a knob/button and some other controls, then right clicking it would lock the dragging state until another left click occurs.
• Fix: Cursor in text edit controls could disappear.
• Fix: MDynamics and MMultiBandDynamics could crash when side-chain EQ was used, displayed and modulated at the same time.
• Fix: MMultiAnalyzer didn't store Global flag for Normalization.

Changes for MPowerSynth in 10.05:

Note: While backward compatibility is strictly maintained, in order to provide higher multiparameter bank mode accuracy, the new format is different from the previous one, hence settings stored with the new versions won't be loaded properly with previous versions. The should be no need to roll back to older versions, but it is an important information anyway.:

• Added Modulation to both taps in Convolution FX.
• Added Crest meter to LoudnessAnalyzer FX.
• When searching through presets the total number of presets are displayed along with the number of matching presets.
• All file browsers now provide Delete key to delete the selected file.
• MultiAnalyzer FX highly optimized.
• Clicking time graph settings while the settings are already open will close the window now.
• VST parameter names are now reported smartly shortened instead of truncated.
• Added DC filter for filters switch to advanced settings and to Wobbler FX.
• Added HP & LP filters to Phatik FX.
• Improved quality of all noise generators and algorithms based on them. Note that there may be a slight difference in sound, hardly noticeable though.
• Auto-listening a band in low-pass/high-pass mode in all parametric equalizers auditions the opposite filter - hence you listen what is being cut.
• Bands in all parametric equalizers/comb filters now also show a line up, for easier workflow when using analyzers. The lines are visible only if the band is enabled.
• System cursors are now used on Windows due to compatibility reasons on some HiDPI devices.
• Style wizard has been discarded. Instead a Set current style as default button has been added.
• Bank values for all multiparameters are now stored with extreme accuracy.
• Added Sync mul to DelayTap and Feedback FX.
• Added Tablet mode back, just in case it is needed.
• Fix: Loading graph presets could lead to have some points in the middle unavailable to move in some places.
• Fix: A multiparameter in Switch mode could cause a freeze in certain situations.
• Fix: Multiparameters accessing ranges of secondary parameters of other multiparameters were not showing the target units.
• Fix: Equalizer/comb points could jump a little when started dragging.
• Fix: Reordering multiparameters sometimes didn't keep relations between different multiparameters controlling each other.
• Fix: Analyzers could crash when changing Time resolution.
• Fix: Left clicking a knob/button and some other controls, then right clicking it would lock the dragging state until another left click occurs.
• Fix: Cursor in text edit controls could disappear.
• Fix: Dynamics FX could crash when side-chain EQ was used, displayed and modulated at the same time.